Pascal

ICSE · Class 7 · Mathematics · Chapter 13

Practical Geometry

Free worksheets and mock tests on this chapter, with answer keys. Make one in about a minute and print it, or take the mock test online and get it marked.

What this chapter covers

  • Construct a line parallel to a given line through a point not on the line using paper folding techniques
  • Construct a line parallel to a given line through a point not on the line using a ruler and compass
  • Explain and justify why the constructed line is parallel using the properties of alternate interior angles or corresponding angles
  • Construct triangles given three side lengths using ruler and compass, and verify triangle properties
  • Construct triangles given two sides and the included angle using ruler, compass, and protractor
  • Construct equilateral and isosceles triangles with specified measurements, and measure unknown angles

Sample questions

Try these, then make a full worksheet or mock test on the chapter. They were written by AI and checked by a second AI, but a mistake can still slip through.

  1. 1.In constructing a triangle ABC with AB = 3.2 cm, BC = 3.9 cm, and ∠B = 120°, what is the correct use of the protractor and compass after drawing segment AB?

    1. A.At A, construct 120° angle; then with A as center and radius 3.9 cm draw an arc to meet AB at C; join BC.
    2. B.At C, construct 120° angle; then with C as center and radius 3.2 cm draw an arc to meet AB at B; join AB.
    3. C.At B, construct 120° angle; then with B as center and radius 3.9 cm draw an arc to meet the ray from B at C; join AC.
    4. D.At B, construct 60° angle; then with B as center and radius 3.9 cm draw an arc to meet AB at C; join AC.
    Show the answer

    Answer: C. At B, construct 120° angle; then with B as center and radius 3.9 cm draw an arc to meet the ray from B at C; join AC.

    The SAS triangle construction requires drawing side AB, then constructing the given angle at B (120°), using compass with BC length as radius to mark point C on ray from B; finally joining A and C completes the triangle.

  2. 2.Which of the following statements about triangle construction is true?

    1. A.A triangle with angles 110° and 80°, and side EF = 7.2 cm, can be constructed.
    2. B.A right angled triangle can be constructed if an acute angle and the hypotenuse are given.
    3. C.A triangle with side lengths 2.5 cm, 3 cm, and 6 cm can be constructed.
    4. D.A triangle with sides 5 cm, 5 cm, and 11 cm can be constructed.
    Show the answer

    Answer: B. A right angled triangle can be constructed if an acute angle and the hypotenuse are given.

    Triangles need to satisfy the triangle inequality: sum of any two sides > third side, so sides 2.5,3,6 or 5,5,11 cannot form triangles. Angles 110° and 80° sum to 190°, exceeding 180°. Given an acute angle and hypotenuse in right-angled triangle is sufficient to construct it.

  3. 3.Triangle XYZ is constructed with XY = 6 cm, ∠X = 30°, and ∠Y = 100°. What is the measure of ∠Z and which construction method best applies here?

    1. A.∠Z = 40°; use SSS method.
    2. B.∠Z = 40°; use ASA method.
    3. C.∠Z = 50°; use SAS (two sides and included angle) method.
    4. D.∠Z = 50°; use ASA (two angles and included side) method.
    Show the answer

    Answer: D. ∠Z = 50°; use ASA (two angles and included side) method.

    Since sum of angles is 180°, ∠Z = 180° - 30° - 100° = 50°. The side XY (6 cm) is included between angles X and Y, so ASA method applies.